Open greenhouse vents from a sensor reading

Parts for one build. Reuse equipment you already own. Quantities are planning quantities unless the creator explicitly specifies a count; kit contents are not additional purchases.

Quantities are for one build. Unless marked source-specified, they are planning quantities; confirm kit contents and the chosen configuration before ordering.

1. Qty. 1Plan / confirm
   Required

   ESP32 development board

   Network motor controller.

   Variant not specified.

   Sources & quantity basis

   Creator source. Planning quantity for one build; check the selected configuration.

   • Source
   • Supporting source

   No exact purchase link verified; confirm the model and requirements above before ordering.

2. Qty. Not statedPlan / confirm
   Required

   BTS7960 motor-driver modules

   Forward/reverse motor drive.

   Two motors are specified, but driver count and current margin are not; size per the actual wiring and stall currents.

   Sources & quantity basis

   Creator source. Planning quantity for one build; check the selected configuration.

   • Source
   • Supporting source

   No exact purchase link verified; confirm the model and requirements above before ordering.

3. Qty. 2Source count
   Required

   24 V DC greenhouse roll-up motor

   Vent actuation.

   Torque, current, travel and motor models not supplied.

   Sources & quantity basis

   Creator source. Source-specified quantity.

   • Source
   • Supporting source

   No exact purchase link verified; confirm the model and requirements above before ordering.

4. Qty. 1Plan / confirm
   Required

   24 V DC power supply

   Motor power.

   Capacity must cover the actual startup/stall load; do not infer it from nominal voltage.

   Sources & quantity basis

   Creator source. Planning quantity for one build; check the selected configuration.

   • Source
   • Supporting source

   No exact purchase link verified; confirm the model and requirements above before ordering.

5. Qty. 1Plan / confirm
   Required

   SwitchBot thermometer/hygrometer

   Temperature input.

   Exact model and hub/connection path not disclosed.

   Sources & quantity basis

   Creator source. Planning quantity for one build; check the selected configuration.

   • Source
   • Supporting source

   No exact purchase link verified; confirm the model and requirements above before ordering.

6. Qty. 1Plan / confirm
   Required

   Manual control switch

   Local override.

   Sources & quantity basis

   Creator source. Planning quantity for one build; check the selected configuration.

   • Source
   • Supporting source

   No exact purchase link verified; confirm the model and requirements above before ordering.

7. Qty. SetPlan / confirm
   Required

   Wiring and terminal blocks

   Power and signal connections.

   Sources & quantity basis

   Creator source. Planning quantity for one build; check the selected configuration.

   • Source
   • Supporting source

   No exact purchase link verified; confirm the model and requirements above before ordering.

8. Qty. Design requiredPlan / confirm
   Required

   Motor stopping, isolation and protection hardware

   End-of-travel and emergency safety.

   Limits, fusing, cutoff, enclosure and low-voltage power conversion are not detailed in the showcase.

   Sources & quantity basis

   Setup requirement — check against your configuration. Planning quantity for one build; check the selected configuration.

   • Source
   • Supporting source

   Use existing equipment or match the specification above. No exact purchase link verified.

9. Qty. SetPlan / confirm
   Tool

   Assembly and test tools

   Assemble and check the circuit.

   Soldering iron, solder, wire cutters and multimeter; review the wiring before power-up.

   Sources & quantity basis

   Setup requirement — check against your configuration. Planning quantity for one build; check the selected configuration.

   • Source
   • Supporting source

   Use existing equipment or match the specification above. No exact purchase link verified.

10. Qty. 1Plan / confirm
    Tool

    Computer for setup

    Build, configure or flash the software.

    Sources & quantity basis

    Setup requirement — check against your configuration. Planning quantity for one build; check the selected configuration.

    • Source
    • Supporting source

    Use existing equipment or match the specification above. No exact purchase link verified.

Source reviewed, not assembled or hands-on tested. A working product page does not confirm stock, firmware compatibility or a complete build.